National Instruments Deterministic Ethernet Expansion Chassis NI 9144 Manual do Utilizador descarregar pdf (Página 43)

NI 9219 Configuration Command

Whether you are using the channel or not, you must configure the

Conversion Time, Mode, Range, and Calibration Gain/Offset values for

each channel on the NI 9219.

Note You must first send calibration gain and offset values in MSB format. The

Conversion Time value must be the same across all channels.

Where:

Table 37. NI 9219 Scan List Format

Bits Field

7:6 Channel Number, 0..3

5 = 0

4:0 Configuration Type

Table 38. NI 9219 Conversion Time Value

Configuration Type Value

Conversion Time 0x1F

Mode & Range 0x01

Calibration Offset 2 (LSB) 0x06

Calibration Offset 1 0x05

Calibration Offset 0 (MSB) 0x04

Calibration Gain 2 (LSB) 0x0A

Calibration Gain 1 0x09

Calibration Gain 0 (MSB) 0x08

1 2 ... 38 39 40 41 42 43 44 45 46 47 48 ... 64 65

Contents 1
Introduction 2
Safety Guidelines 3
Mounting the NI 9144 Chassis 4
20 W MAX 5
Chassis on a Panel 6
Understanding LED Indications 10
Figure 10. EtherCAT Modes 11
Safe-State Outputs 12
Slave Timing Modes 12
Updating your Firmware 12
Using AoE/SDO 13
Using CoE/SDO 13
Specifications 14
Hazardous Locations 15
Environmental 15
Shock and Vibration 16
Safety Standards 17
Electromagnetic Compatibility 17
⬉ᄤֵᙃѻક∵ᶧ᥻ࠊㅵ⧚ࡲ⊩ ˄Ё೑ 18
Appendix A 19
Supported C Series Modules 20
NI 9201/9221 21
NI 9201/9221 Scan List 22
NI 9201/9221 Calibration Data 23
NI 9203 Scan List 24
NI 9203 Calibration Data 26
Signed pA 27
NI 9205/9206 28
NI 9205/9206 Scan List 28
NI 9205/9206 Calibration Data 30
NI 9211 Scan List 31
NI 9211 Calibration Data 32
NI 9213 Scan List 33
NI 9213 Calibration Data 34
NI 9215 Calibration Data 35
NI 9217 Scan List 36
NI 9217 Calibration Data 37
Signed μΩ 38
NI 9219 ADC Format 39
NI 9219 Error Status 40
NI 9219 Calibration Data 40
0 Volts 41
0x7F Data Byte 45
0xFF Data Byte 45
0x85 Data Byte 45
0x86 Data Byte 46
0xC8 Data Byte 47
0xD3 Data Byte 48
NI 9233 Configure ADC 49
OCLK pin is used as the 50
OCLK pin. Currently 50
NI 9233 Calibration Data 51
NI 9234 Configure Module 52
OCLK pin 53
OCLK pin. Currently, this is 53
NI 9234 Example Data Rates 54
NI 9234 Calibration Data 54
NI 9237 Configure Module 55
NI 9237 Example Data Rates 57
NI 9237 Calibration Data 58
NI 9229/9239 58
NI 9229/9239 Calibration Data 59
NI 9263 Calibration Data 60
NI 9264 Calibration Data 61
NI 9265 Error Status 62
NI 9265 Calibration Data 62
NI 9401 Direction Control 63
NI 9403 Direction Control 64
NI 9476 Error Status 64
Where to Go for Support 65

Comentários a estes Manuais

Sem comentários

National Instruments Deterministic Ethernet Expansion Chassis NI 9144 Manual do Utilizador Página 43

Comentários a estes Manuais